Reverse engineering and import substitution

We reproduce equipment that is no longer supplied

We restore design documentation and manufacture parts, assemblies, instruments and electronic units that have no drawings, spares or manufacturer support. From a sample to a tested product with documentation.

When it is needed

The equipment works, but support is gone

The foreign manufacturer has left the market, spares are not supplied, and a stopped line or vessel costs more than any part. Reverse engineering solves this without grey-market supplies: the product is reproduced from a sample and receives full documentation.

This is not limited to offshore. We apply the same approach to production lines and everything related to them — including high-precision manufacturing, where tolerances, repeatability and documented quality matter.

  • no drawings or technical documentation for the assembly
  • the spare part is discontinued or cannot be ordered
  • the lead time for the original is measured in months
  • a domestic equivalent with local service is required
  • the original has a weak point that should be fixed
What we take on

From a single part to a control unit

01

Machine parts and assemblies

Shafts, housings, fastening and sealing assemblies, hydraulic and pneumatic components, gearboxes, pump parts, wear parts. We select material and coating for the operating conditions rather than simply “as it was”.

02

Production line equipment

Assemblies and modules of assembly, conveying and packaging lines, grippers, drives, tooling, replaceable and wear parts. For high-tech manufacturers we develop design documentation for remote tooling, manipulators and robots and manufacture special fixtures — we bring this high-precision manufacturing experience to reverse-engineering tasks.

03

Electronics and automation

Replacement of control units, sensors and boards with our own designs. We write control software for automated assembly stations and lines and take it through commissioning, so we can reproduce not only the hardware but also the logic of the unit.

04

Subsea and marine equipment

Skids and tooling for ROVs, ship machinery, spares for underwater vehicles. This is where we have the longest list of our own products that replaced imported equivalents.

05

Special tooling and fixtures

Fixtures, test rigs and tools for a specific process operation — when no ready-made solution exists or it is unavailable.

How we work

Full cycle in six steps

01

Sample examination

We study the product, its operating conditions and failure causes, and record what must be kept and what should be improved.

02

Measurement and 3D model

We capture the geometry and build a 3D model of the part or assembly.

03

Calculations

We verify strength and stiffness analytically and by the finite element method; for subsea equipment, corrosion resistance as well.

04

Documentation

We issue a design documentation package from which the product can be manufactured repeatedly.

05

Manufacturing

We manufacture at our own production sites and at partner facilities: machining, welding and assembly, electronics.

06

Testing

We test the product to an agreed procedure and hand it over with documentation.

Result

What the customer receives

A documented product

Not a one-off copy but a product with a documentation package: it can be produced in series and serviced in Russia.

Weak points corrected

If the original had vulnerable assemblies, we improve them rather than repeat them.

Calculations and test procedures

Each solution is confirmed by calculation and verified by testing — essential for acceptance at critical facilities.

Warranty and support

Products are covered by warranty; we stay in touch after handover and remain responsible for the result.

Examples

What we already make ourselves instead of importing

Amaringo's own products for subsea engineering works. Such equipment used to be purchased abroad; now it is designed and manufactured in Russia — with calculations, documentation and service.

Industries

Where it applies

We take tasks from any industry: the engineering approach is the same, only the product requirements change.

  • Industrial equipment. Parts of machine tools and production lines, pumps, gearboxes, hydraulics, tooling.
  • High-precision manufacturing. Remote tooling, manipulators, special fixtures, assemblies of automated stations.
  • Energy and oil and gas. Valves, compressor and drilling equipment assemblies, special tools.
  • Shipbuilding and marine equipment. Ship machinery, subsea equipment, spares for underwater vehicles.
  • Transport and special vehicles. Components for railway, road, mining and agricultural machinery.
  • Food and packaging industry. Wear parts and assemblies for filling and packing lines.
  • Medicine. Assemblies and spares for diagnostic, laboratory and sterilisation equipment.
  • Electronics and automation. Control units, sensors and boards.
Questions and answers

Reverse engineering

Can a part be reproduced without drawings?

Yes. Documentation is restored from the sample: measurement, 3D model, calculations and a design documentation package. After that the product can be manufactured repeatedly.

Do you work only with marine and subsea equipment?

No. Subsea equipment is where Amaringo has the most products of its own, but reverse engineering is also carried out for production lines, machine tools, tooling, electronics and automation, including high-precision manufacturing.

Do you make an exact copy of the original?

The product reproduces the function and interface dimensions of the original. Weak points — material, coating, design of a vulnerable assembly — are improved in agreement with the customer.

Do you take on electronic units and control systems?

Yes. Amaringo replaces control units, sensors and boards with its own designs and writes control software.

Can I order a single part?

Yes. The company produces both one-off and series units.

How much does reverse engineering cost and how long does it take?

Price and lead time depend on product complexity, accuracy requirements and the scope of testing. They are defined after examining the sample and agreeing the technical specification.

Where do I start?

Send photos of the product and a description of the task and operating conditions to info@amaringo.ru or call +7 (812) 426-09-62. This is enough for an initial assessment.

Send a photo of the part or assembly — we will assess the task